Search Results

Abstract A wind-tunnel study was undertaken to investigate the drag reduction potential of two-truck platooning, in the context of understanding some of the factors that may influence the potential fuel savings and greenhouse-gas reductions. Testing was undertaken in the National Research Council Canada 2 m × 3 m Wind Tunnel with two 1/15-scale models of modern aerodynamic tractors paired with dry-van trailers configured with and without combinations of side-skirts and boat-tails. Separation distances of 0.14, 0.28, 0.49, 0.70 and 1.04 vehicle lengths were tested (3 m, 6 m, 10.5 m, 15 m, and 22.5 m full scale). Additionally, within-lane lateral offsets up to 0.31 vehicle widths (0.8 m full scale) were evaluated, along with a full-lane offset of 1.42 vehicle widths (3.7 m full scale). This study has made use of a wind-averaged-drag coefficient as the primary metric for evaluating the effect of vehicle platooning.

Abstract TOC

Abstract TOC

Abstract Diesel trucks play a crucial role in transportation activity and a major contributor to fuel consumption and air pollution. To improve the energy efficiency of diesel trucks, we develop a truck eco-approach and departure (EAD) system based on Signal Phase and Timing (SPaT) message from signal controllers and road grade information along the path. The proposed model consists of two levels—the lower level for powertrain-based fuel consumption estimation and the upper level for optimal trajectory planning. The powertrain model is designed for a diesel engine with a six-gear transmission and well calibrated using on-board Electronic Control Unit (ECU) data. The trajectory planning model is formulated as a shortest path problem with the combination of time, distance, and speed as the state on each node and fuel consumption rate as the cost on state transition.

Abstract Regulations limiting GreenHouse Gases (GHG) from Heavy-Duty (HD) commercial vehicles in the United States (US) and European Union will phase in between the 2024 and 2030 model years. These mandates require efficiency improvements at both the engine and vehicle levels, with the most stringent reductions required in the heaviest vehicles used for long-haul applications. At the same time, a 90% reduction in oxides of nitrogen (NOx) will be required as part of new regulations from the California Air Resources Board. Any technologies applied to improve engine efficiency must therefore not come at the expense of increased NOx emissions. Research into advanced engine architectures and components has identified improved turbomachine efficiency as one of the largest potential contributors to engine efficiency improvement. However this comes at the cost of a reduced capability to drive high-pressure Exhaust Gas Recirculation (EGR).

Abstract The current publication considers several methodologies to minimize tailpipe (TP) nitrogen oxides (NOx) emissions during cold start operation. A standard, 2019 aftertreatment design of diesel oxidation catalyst (DOC), diesel particulate filter (DPF), and selective catalytic reduction (SCR)/ammonia oxidation catalyst (AMOX) was used as the baseline. Cold start NOx conversion and TP NOx emissions improvements were measured when a larger SCR, dual diesel exhaust fluid (DEF) dosing, and an electric heater were added to the exhaust configuration. Additional improvements were achieved by an improved cold start combustion mode was developed.

Abstract As emissions regulations continue to tighten, both from lower imposed limits of pollutants, such as nitrous oxides (NOx), and in-use and real-world testing, the importance of quickly heating the aftertreatment to operating temperature during a cold start, as well as maintaining this temperature during periods of low engine load, is of increasing importance. Perhaps the best method of providing the necessary heating of the aftertreatment is to direct hot exhaust gasses to it directly from the engine. For heavy-duty diesel engines that utilize turbochargers, this is achieved by fully bypassing the exhaust flow around the turbine directly to the aftertreatment. However, this disables a conventional turbocharger, limiting engine operation to near-idle conditions during the bypass period.

Abstract Traditionally, in combustion engine applications, metallic materials have been widely employed due to their properties: castability and machinability with accurate dimensional tolerances, good mechanical strength even at high temperatures, wear resistance, and affordable price. However, the high thermal conductivity of metallic materials is responsible for consistent losses of thermal energy and has a strong influence on pollutant emission. A possible approach for reducing the thermal exchange requires the use of thermal barrier coating (TBC) made by materials with low thermal conductivity and good thermo-mechanical strength. In this work, the effects of a ceramic coating for thermal insulation of the piston crown of a car diesel engine are investigated through a numerical methodology based on finite element analysis. The study is developed by considering firstly a thermal analysis and then a thermo-structural analysis of the component.

Abstract In this study low temperature plasma technology was applied to expand auto-ignition operation region and control auto-ignition phasing of the homogeneous charge compression ignition (HCCI) combustion. The low temperature plasma igniter of a barrier discharge model (barrier discharge igniter (BDI)) with high-frequency voltage (15 kHz) was provided at the top center of the combustion chamber, and the auto-ignition characteristics of the HCCI combustion by the low temperature plasma assistance was investigated by using a single-cylinder gasoline engine. HCCI combustion with compression ratio of 15:1 was achieved by increasing the intake air temperature. The lean air-fuel (A/F) ratio limit and visualized auto-ignition combustion process on baseline HCCI without discharge assistance, spark-assisted HCCI, and BDI-assisted HCCI were compared.

Abstract The article describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components’ light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features has been thoroughly experimentally examined.

Abstract Insulating combustion chamber surfaces with thermal barrier coatings (TBCs) provides thermal efficiency improvement when done appropriately. This article reports on insulation heat transfer, engine performance characteristics, and damage modelling of “temperature swing” TBCs. “Temperature swing” insulation refers to the insulation material applied on surfaces of combustion chamber walls that enables selective manipulation of its surface temperature profile over the four strokes of an engine cycle. A combined GT Suite-ANSYS Fluent simulation methodology is developed to investigate the impact of thermal properties and insulation thickness for a variety of TBC materials for its “temperature swing” characteristics. This one-dimensional transient heat conduction analyses and engine cycle simulations are performed using scaled-down thermal properties of yttria-stabilized zirconia.

Abstract Reactivity-controlled compression ignition (RCCI) is a dual fuel low temperature combustion (LTC) strategy which results in a wider operating load range, near-zero oxides of nitrogen (NOx) and particulate matter (PM) emissions, and higher thermal efficiency. One of the major shortcomings in RCCI is a higher unburned hydrocarbon (HC) and carbon monoxide (CO) emissions. Unlike conventional combustion, aftertreatment control of HC and CO emissions is difficult to achieve in RCCI owing to lower exhaust gas temperatures. In conventional RCCI, an early direct injection (DI) of low volatile diesel fuel into the premixed gasoline-air mixture in the combustion chamber results in charge stratification and fuel spray wall wetting leading to higher HC and CO emissions. To address this limitation, a homogeneous charge reactivity-controlled compression ignition (HCRCCI) strategy is proposed in the present work, wherein the DI of diesel fuel is eliminated.

Abstract A new method that allows data-enabled (empirical) models, commonly used for automotive engine calibration, to extrapolate beyond the range of training data has been developed. This method used a physics-based system-level one-dimensional model to improve interpolation and allow extrapolation for three data-based algorithms, by modifying the model input (feature) space. Neural network, regression, and k-nearest neighbor predictions of engine emissions and volumetric efficiency were greatly improved by generating 736,281 artificial feature spaces and then performing feature selection to choose feature spaces (feature selection) so that extrapolations in the original feature space were interpolations in the new feature space. A novel feature selection method was developed that used a two-stage search process to uniquely select the best feature spaces for every prediction.

Abstract The wide application of Gasoline Direct Injection (GDI) engines and the increasingly stringent Particulate Matter (PM) and Particulate Number (PN) regulations make Gasoline Particulate Filters (GPFs) with high filtration efficiency and low pressure drop highly desirable. However, due to the specifics of GDI operation and GDI PM, the design of these filters is even more challenging as compared to their diesel counterparts. Computational Fluid Dynamics (CFD) studies have been shown to be an effective way to investigate filter performance. In particular, our previous two-dimensional (2D) CFD study explicated the pore size and pore-size distribution effects on GPF filtration efficiency and pressure drop. The “throat unit collector” model developed in this study furthers this work in order to characterize the GPF wall microstructure more precisely.

Abstract Federal Aviation Administration (FAA)’s 20 years of research and development with 200 unleaded blends and full-scale engine tests on 45 high-octane unleaded blends has not found a “drop-in” unleaded replacement for aviation gasoline (AVGAS) 100 low lead (100LL) fuel. In this study, analysis of compatibility via optimization of Lycoming O-320 engine fuelled with RON 97, RON 98, RON 100, and AVGAS was conducted using the Response Surface Methodology (RSM). Test fuels were compositionally characterized based on Gas Chromatography (GC) analysis and were categorized based on types of Hydrocarbon (HC). Basic fuel properties of fuels in this research were analyzed and recorded. For optimization analysis, engine speed and fuel were considered as the input parameters.

Abstract The Formula SAE (FSAE) is an international engineering competition where a Formula style race car is designed and built by students from worldwide universities. According to FSAE regulation, an air restrictor with circular cross section of 20 mm for gasoline-fuelled and 19 mm for E-85-fuelled vehicles is to be incorporated between the throttle valve and engine inlet. The sole purpose of this regulation is to limit the airflow to the engine used. The only sequence allowed is throttle valve, restrictor and engine inlet. A new approach of combining ram theory and acoustic theory methods are investigated to increase the performance of the engine by designing an optimized intake runner for a particular engine speed range and an optimized plenum volume in this range. Engine performance characteristics such as brake power, brake torque and volumetric efficiency are taken into considerations.

Abstract This study shows the development of low-temperature and high-temperature reactions in a gasoline-fuelled compression ignition (GCI) engine realizing partially premixed combustion for high efficiency and low emissions. The focus is how the ignition occurs during the low- to high-temperature reaction transition and how it varies due to single- and double-injection strategies. In an optically accessible, single-cylinder small-bore diesel engine equipped with a common-rail fuel injection system, planar laser-induced fluorescence (PLIF) imaging of formaldehyde (HCHO-PLIF), hydroxyl (OH-PLIF), and fuel (fuel-PLIF) has been performed. This was complemented with high-speed imaging of combustion luminosity and chemiluminescence imaging of cool flame and OH*.

Abstract In order to meet the worldwide increasingly stringent particulate matter (PM) and particulate number (PN) emission limits, the diesel particulate filter (DPF) is widely used today and has been considered to be an indispensable feature of modern diesel engines. To estimate the soot loading amount in the DPF accurately and in real-time is a key function of realizing systematic and efficient applications of diesel engines, as starting the thermal regeneration of DPF too early or too late will lead to either fuel economy penalty or system reliability issues. In this work, an open-loop and on-line approach to estimating the DPF soot loading on the basis of soot mass balance is developed and experimentally investigated, through establishing and combining prediction models of the NOx and soot emissions out of the engine and a model of the catalytic soot oxidation characteristics of passive regeneration in the DPF.

Abstract Higher water evaporation and proper water vapor distribution in the cylinder are very vital for improving emission and performance characteristics of water-injected engines. The concentration of water vapor should be higher and uniform near the walls of the combustion chamber and nil at the spark plug location. In direct water-injected engines, water evaporation, vapor distribution, and spray impingement are highly dependent on injector parameters, viz., water injector orientation (WIO), location, and spray angle. Therefore, in this article, a computational fluid dynamics (CFD) investigation is conducted to study the effects of water injector spray angle (WISA), and WIO on the water evaporation, emission, and performance characteristics of a four-stroke, wall-guided gasoline direct injection (GDI) engine. The WISA is varied from 10° to 35°, whereas the WIO is varied from 15° to 35° in steps of 5°.

Abstract One of the key factors for accurate mass burn fraction and energy conversion point calculations is the accuracy of the compression ratio. The method presented in this article suggests a workflow that can be applied to determine or correct the compression ratio estimated geometrically or measured using liquid displacement. It is derived using the observation that, in a motored engine, the heat losses are symmetrical about a certain crank angle, which allows for the derivation of an expression for the clearance volume [1]. In this article, a workflow is implemented in real time, in a current production engine indicating system. The goal is to improve measurement data quality and stability for the energy conversion points calculated during measurement procedures. Experimental and simulation data is presented to highlight the benefits and improvement that can be achieved, especially at the start of combustion.